120W LED Street Lighting Upgrade with Intelligent Lighting Control
Project Location: Rotterdam, Netherlands
Project Type: Municipal Road Lighting Upgrade
Product: LED Street Lights
Project Quantity: 2,000 sets
Rated Power: 120W
Certification: CE
Warranty: 3 Years
Energy-Saving Target: 25%
Lighting Control: Microwave Motion Sensor + Light Control + Timer Control
Project Overview
The Rotterdam municipal road lighting project focused on upgrading existing roadway lighting with a more efficient LED lighting system and intelligent control architecture.
The project used 2,000 sets of 120W LIKELITE LED Street Lights, configured for AC230V / 50Hz operation and supported by professional lighting design and engineering services.
The project scope covered more than fixture supply.
LIKELITE supported the lighting engineering process through:
Onsite Metering → Lighting Design → Simulation → Electrical Layout → Product Supply → Installation Support
The project was designed around three primary objectives:
Improve lighting system efficiency.
Reduce municipal lighting energy consumption.
Introduce more flexible lighting control.
Project at a Glance
| Project Item | Specification |
|---|---|
| Location | Rotterdam, Netherlands |
| Application | Municipal Roadway Lighting |
| Product | LED Street Lights |
| Quantity | 2,000 sets |
| Power | 120W |
| Certification | CE |
| Input Voltage | AC230V |
| Frequency | 50Hz |
| IP Rating | IP65 |
| LED Source | Lumileds SMD2835 |
| Luminous Efficiency | 120 lm/W |
| Beam Angle | 120° |
| Surge Protection | 10KV |
| Voltage Resistance | 1.5KV |
| CCT | 5000K ± 500K |
| CRI | Ra 80 |
| Housing | Aluminum Alloy |
| Optical Material | PC |
| Lifespan | 30,000 hours |
| Working Temperature | -20°C to +45°C |
| Warranty | 3 years |
| Control System | Microwave Motion Sensor + Light Control + Timer Control |
| Energy-Saving Target | 25% |
Project Requirements
Municipal roadway lighting upgrades normally need to address existing infrastructure, electrical conditions, lighting distribution, operating schedules, and maintenance requirements at the same time.
For this project, the lighting system was configured around the following requirements:
Efficient LED Replacement
The project specified 120W LED Street Lights with a rated luminous efficiency of 120 lm/W.
Outdoor Protection
The fixtures use an IP65 protection rating for outdoor roadway applications.
Electrical Compatibility
The reference configuration operates at:
AC230V / 50Hz
with 10KV surge protection and 1.5KV voltage resistance specified for the fixture.
European Certification
The project configuration uses CE-certified LED Street Lights.
Intelligent Lighting Control
The project incorporates:
Microwave Motion Sensor + Light Control + Timer Control
to provide more flexible control of roadway lighting operation.
Long-Term Project Support
A 3-year warranty was specified for the project.
LED Street Light Configuration
120W LIKELITE LED Street Light
The selected fixture combines an aluminum alloy housing with PC optical material.
Optical Configuration
LED Source: Lumileds SMD2835
Luminous Efficiency: 120 lm/W
Beam Angle: 120°
CCT: 5000K ± 500K
CRI: Ra 80
The optical configuration is intended for roadway lighting applications where consistent light distribution and efficient LED performance are required.
Electrical & Protection Configuration
Input Voltage: AC230V
Frequency: 50Hz
Power Supply: AC
Surge Protection: 10KV
Voltage Resistance: 1.5KV
IP Rating: IP65
The electrical configuration was selected for the project's European AC power environment and outdoor municipal roadway application.
Intelligent Lighting Control System
A major part of the project was the integration of three control functions.
Microwave Motion Sensor
Motion detection can be used to respond to movement within the configured detection area.
This provides a control option for roads where traffic activity varies during the night.
Light Control
Light-control functionality can be used to manage operation according to ambient lighting conditions.
Timer Control
Timer-based operation allows lighting schedules to be configured according to municipal operating requirements.
Combined Control
Microwave Motion Sensor + Light Control + Timer Control
The three functions provide a more flexible operating structure than a simple fixed ON/OFF lighting schedule.
The exact control parameters should be configured according to the final municipal operating strategy.
Engineering Services
The Rotterdam project was supported by a complete lighting engineering workflow.
Onsite Metering
Existing project conditions can be measured and reviewed before finalizing the lighting configuration.
Lighting & Circuitry Design
Lighting positions and electrical circuitry can be coordinated with the roadway infrastructure.
DIALux Evo Layout
DIALux Evo can be used to establish the roadway lighting model and evaluate the proposed lighting arrangement.
Litepro DLX Layout
Litepro DLX layout support is available for projects requiring this design workflow.
AutoCAD Layout
CAD drawings can be prepared for engineering coordination and project implementation.
AGi32 Layout
AGi32-based lighting calculation and layout support can also be provided when required.
Project Installation
Installation support forms part of the project delivery scope according to the agreed project requirements.
Project Implementation
01 — Existing Condition Assessment
The project starts with an understanding of the existing roadway lighting environment.
Key information includes:
Existing fixture type
Fixture wattage
Pole height
Pole spacing
Road width
Electrical supply
Operating schedule
Existing control method
02 — Lighting Design
The roadway configuration is translated into a lighting model.
The engineering team can use the project road geometry, pole arrangement, fixture optical distribution, mounting height, and operating requirements to establish the proposed layout.
03 — Product Configuration
The final fixture configuration is matched to the project requirements.
For this project:
120W + 120 lm/W + IP65 + Lumileds SMD2835 + 10KV Surge + Intelligent Control
04 — Product Supply
A total of:
2,000 Sets
of LED Street Lights were specified for the project.
The fixtures were configured for:
AC230V / 50Hz
European project requirements.
05 — Installation & Commissioning
Project installation follows the approved lighting and electrical layout.
After installation, the lighting system and control functions can be checked before project handover.
Project Result
Energy-Saving Target: 25%
The Rotterdam project specifies an energy-saving target of 25%.
The potential energy-saving performance of a municipal lighting upgrade depends on:
Existing fixture wattage
LED replacement wattage
Annual operating hours
Existing control strategy
Motion-sensing settings
Timer settings
Ambient-light control
Actual roadway operating conditions
Therefore, the 25% figure should be treated as the project-specified energy-saving result/target provided for this case, rather than applying it universally to all municipal projects.
Project Technical Result
The project combines:
120W LED Technology
A 120W LED Street Light configuration with 120 lm/W luminous efficiency.
Intelligent Control
Microwave Motion Sensor + Light Control + Timer Control
Outdoor Protection
IP65
Electrical Protection
10KV Surge Protection
European Electrical Configuration
AC230V / 50Hz
Long-Term Support
3-Year Warranty
Before & After Comparison
DIALux EVO Lighting Simulation Verification
Project Product Details
LIKELITE 120W LED Street Light
Brand: LIKELITE
Origin: Guangdong, China
Product: LED Street Lights
Power: 120W
Input Voltage: AC230V
Frequency: 50Hz
LED Source: Lumileds SMD2835
Luminous Efficiency: 120 lm/W
Beam Angle: 120°
IP Rating: IP65
Surge: 10KV
Voltage Resistance: 1.5KV
CCT: 5000K ± 500K
CRI: Ra 80
Material: Aluminum Alloy + PC
Lifespan: 30,000 Hours
Operating Temperature: -20°C to +45°C
Warranty: 3 Years
Project Supply Information
Single Package Size: 56 × 18 × 7 cm
Single Gross Weight: 7 kg
These logistics specifications can be used for project packaging, transportation, and installation planning.
Why This Project Matters
The Rotterdam project demonstrates a project-based approach to municipal roadway lighting:
Existing Roadway → Engineering Assessment → Lighting Design → LED Upgrade → Intelligent Control → Installation → Commissioning
The value of the project is not only the replacement of 2,000 street lights.
It is the integration of:
LED Efficiency + Lighting Engineering + Electrical Design + Intelligent Control + Project Delivery
into one municipal lighting upgrade process.
Similar Municipal Lighting Projects
LIKELITE can support similar projects for:
Municipal road upgrades
Urban street lighting
Residential road lighting
Public infrastructure
City roadway renovation
Road lighting replacement
Energy-saving lighting upgrades
Intelligent street lighting projects
Municipal Lighting Project FAQ
1. Where is the Rotterdam project located?
The project is located in Rotterdam, Netherlands and is described as a municipal roadway lighting upgrade.
2. How many LED Street Lights were specified?
The project quantity is 2,000 sets.
3. What wattage was used?
The project uses 120W LED Street Lights.
4. What is the LED luminous efficiency?
The specified luminous efficiency is 120 lm/W.
5. What LED chip is used?
The fixture uses Lumileds SMD2835 LED.
6. What certification does the project use?
The specified certification is CE.
7. What is the IP rating?
The fixture is specified with IP65 protection.
8. What intelligent control system is used?
The project uses:
Microwave Motion Sensor + Light Control + Timer Control.
9. What is the project's energy-saving target?
The specified energy-saving target is 25%.
Actual savings depend on the original lighting system and final operating conditions.
10. What is the warranty period?
The project specifies a 3-year warranty.
11. What electrical input is used?
The fixture configuration is:
AC230V / 50Hz.
12. What surge protection is specified?
The fixture specifies 10KV surge protection.
13. Can LIKELITE provide DIALux calculations for similar projects?
Yes. LIKELITE can provide DIALux Evo lighting layout and calculation support according to project requirements.
14. Can LIKELITE provide installation support?
Yes. Project installation support can be included according to the agreed project scope.
15. Can LIKELITE develop a similar solution for another city?
Yes. A similar project can be evaluated based on road layout, pole height, pole spacing, existing fixture specifications, operating hours, local standards, and required lighting performance.
Request a Similar Municipal Lighting Project
Planning a Municipal Road Lighting Upgrade?
Send LIKELITE:
Road Layout + Existing Lighting Data + Pole Information + Quantity + Local Standards + Control Requirements
Our engineering team can evaluate the project and develop a project-specific LED roadway lighting configuration.
LIKELITE — LED Lighting Solutions for Municipal Infrastructure Projects.
